Vehicles
Sections
322 not categorized PORSCHE 924 S WE NEED A CARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 TURBO/GT2 2007-09 (includes uncategorized and accessory items) 93060290202A Worn or cracked distributor rotors can create misfires and poor starts. Replace yours with a genuine beru distributor rotor. Sold individually. 1 necessary per distributor.
$15.40
Make a selection 93060290401A Distributor caps are often overlooked as the source of ignition issues. If yours is failing or cracked, you can experience shaking at idle, poor starting in the cold, stalling and backfiring. Be sure to replace it if you see any signs of cracking. This is a high-quality beru replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $26.40
Make a selection 93061221102 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle.
From $13.02
Make a selection 96410432100 As valve guides age, they lose their ability to locate the valve to the valve seat. That can create a loss of performance due to the ineffective seal of the combustion chamber. Be sure to replace your guides when replacing valves, valve springs, etc. Sold individually. 6 necessary per vehicle.
From $20.90
Make a selection 96414718703EQ Remove the power steering belt cover to inspect your toothed steering belt for wear and cracking. Belts undergo a lot of friction and wear, so replacing them periodically will prevent damage. Be sure to follow recommended service and replacement intervals set by Porsche on belts or examine the power steering pump belt at each oil change. Sold individually. 1 necessary per car.
$68.20
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 96453109500EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 96453109600EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 964541225001 This genuine Porsche windshield seal is an integral part of keeping your cowl from rusting. It is critical that the gasket and windshield are properly installed to prevent corrosion. Sold individually. 1 needed per car. Please note: for the 911 models, this does not contain the trim frame slot for chrome / black trim like the earlier cars.
$406.00
Make a selection 99157362300 A clean cabin air filter reduces dust, dirt, allergens and odor. It will also increase the airflow from the cabin vents. Be sure to replace yours as recommended to keep consistent air quality. High-quality mann OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment since this fits multiple models / applications. We also recommend replacing the exterior cabin air filter, part # 99157237100
From $22.25
Make a selection 99110613802 The radiator is a critical engine component that needs to be inspected and cleaned of debris to keep them functioning efficiently. If damage is noticed, replace it with this hello OEM high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend replacing the upper and lower rubber mounts, part # 99110653701 and 99110653802 sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. This part is the latest supersession and can also be used in place of part number 991 106 138 01.
From $1,042.80
Make a selection 99157237100 A clean cabin air filter reduces dust, dirt, allergens and odor. It will also increase the airflow from the cabin vents. Be sure to replace yours as recommended to keep consistent air quality. High-quality mann OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment since this fits multiple models / applications. We also recommend replacing the interior cabin air filter, part # 99157362300
From $13.00
Make a selection 99160918100 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle.
From $12.10
Make a selection 99162890100 Wiper blades are a critical safety component that should be changed as soon as visibility is compromised. Replace them with this genuine left-hand driver wiper blade set that includes installation clips. Sold as a set. Driver and passenger fitment. 1 necessary per car. Please note: these fit multiple models / applications. Please check the model fitment tab to ensure accurate fitment.
From $30.50
Make a selection 99334703104 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.
$216.29
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.75
Make a selection 99610090399 Head gasket set for 996 turbo and GT2 exclusive from FVD ! Set contains all gaskets and seals for an engine overhaul. Please order crankcase gasket set (996 100 996 tuam)separately.
$1,542.20
Make a selection 99660410702 If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle actually starting. Eventually you hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter be sure to check the rubber cap on the terminal for cracks which allows moisture in and it is a good idea to check your starters hardware as well. This is the latest supersession from the manufacturer. For the early air cooled car restorations, please note that the housing looks different than the original. Sold individually. This is a new starter so a core charge is not applied. View/Change Diagram
From $260.00
Make a selection BES98115001SK This is our jekyll and hyde version ! The perfect compromise for you and your loved ones. Rich, deep race car tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english, and is the best choice for a daily driver. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared t...(choose a part on the right to read more)
$5,197.50
Make a selection 9A160410400EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$506.00
Make a selection A1126 The girodisc system is a direct replacement for the oe disc on all 997.2 GT3/gt2's, with or without the OEM pccb rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with oe calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your abs efficiency. General Fitment911 TURBO/GT2 2007-09911 GT3 2007-11 911 TURBO/GT2 2010-13
$2,160.00
Make a selection AP3POR001 Throw away your gauges! The new in cabin mountable accessport v3 has a large, full color, higher resolution screen which allows you to monitor up to six parameters in real time. Fully customizable from the look (multiple bezel colors), layout (set up a race, street or dyno gauge cluster) and mounting options (choose from 1,000s of standard vehicle mounts). Of course, all of the great cobb tuning is included with enough space for 100 calibrations. This is your new accessport and maybe the last one you'll ever need. General Fitment911 TURBO/GT2 2007-09
$2,497.50
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection BES91105000SST This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,142.80
Make a selection BES96405000S1 This muffler produces a glorious flat six race car with low deep tones that reminds us of the 964 cup. It is manufactured in Germany by m&m exhaust, gmbh. This muffler is ideal for anyone who wants a lower deeper tone with more decibels, whether they are just replacing the side muffler or are running cat bypass, sport cats or a cup pipe. + 14 hp (10 kw) & + 15 tq (20 nm) gain. - 2 3/4 tubing (70mm). - weighs 13.8 lbs (6.3 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions. - includes factory style hangars and new aero quip style clamps for simple installation. We recommend replacing your exhaust tip with this u...(choose a part on the right to read more)
$1,438.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |